BlueprintCalcs 2D Parametric Trade Tools
Contractor Agreements & Liability Boundaries

Terms of Service

Effective Date: November 18, 2026 • Last Reviewed: November 2026

⚠️ Critical Structural & Engineering Notice

BlueprintCalcs provides mathematical layout aids and parametric diagrams for preliminary estimation and job-site visualization. Our tools do not produce certified, stamped architectural construction documents or professional engineering calculations. Always have your plans verified by a licensed Professional Engineer (PE), registered Architect (RA), or your local municipal building department (AHJ) prior to physical cutting, excavation, or installation.

1. Acceptance of Terms

By accessing, browsing, printing cut sheets from, or using the calculation engines on BlueprintCalcs ("the Service", "blueprintcalcs.com"), you acknowledge that you have read, understood, and agree to be legally bound by these Terms of Service. If you do not agree with any portion of these terms, you must discontinue use immediately.

2. Nature of the Service: Mathematical Estimation Aids

The calculators, parametric 2D SVG diagrams, and printable cut sheets provided on BlueprintCalcs are mathematical models based on published reference guidelines, including:

  • Framing & Carpentry: International Residential Code (IRC) Section R311.7 (Stairways), R802 (Roof Framing), and R602 (Wall Construction).
  • Hardscape & Masonry: ASTM C33 (Concrete Aggregates), ASTM C90 (Hollow Load-Bearing CMU), and ICPI paver bedding standards.
  • Electrical & HVAC: National Electrical Code (NEC / NFPA 70 Article 310, Chapter 9 Tables) and ACCA Manual D guidelines.

While we strive for absolute mathematical precision with unit-tested TypeScript engines, local building codes frequently supersede model codes. Municipalities, counties, and regional jurisdictions regularly adopt amendments governing minimum headroom, seismic hold-downs, snow load derating, wind uplift straps, frost line footing depths, and electrical wire gauges.

3. Contractor & User Responsibility

As the contractor, builder, tradesperson, or property owner using this Service, you assume full responsibility for:

  • Independently pulling building permits and scheduling required municipal inspections.
  • Verifying exact on-site rough opening dimensions, finished floor heights, stringer run clearances, and trench depths with physical tape measures before making saw cuts.
  • Accounting for job-site material variations, such as lumber crown direction, wet soil compaction shrinkage, and aggregate bulk density variations.
  • Calling 811 (utility locates) before performing any excavation calculated via our earthwork tools.

4. Disclaimer of Warranties ("As-Is" Standard)

BlueprintCalcs and all associated blueprints, formulas, text, diagrams, and export files are provided on an "AS-IS" and "AS-AVAILABLE" basis without warranties of any kind, whether express, statutory, or implied.

We expressly disclaim all warranties, including but not limited to the implied warranties of merchantability, fitness for a particular building project, structural integrity, and non-infringement. We do not warrant that calculations will be uninterrupted, error-free, or meet specific municipal inspection requirements.

5. Limitation of Liability

To the maximum extent permitted by applicable law, in no event shall BlueprintCalcs, its creators, contributors, or operators be liable for any direct, indirect, incidental, special, consequential, or punitive damages.

This limitation applies to, but is not limited to: structural failures, municipal inspection red tags or rejections, job-site injuries, material mis-orders or waste, project timeline delays, labor costs, or commercial losses arising out of or related to the use of or inability to use our tools.

6. Indemnification & Hold Harmless

You agree to defend, indemnify, and hold harmless BlueprintCalcs, its creators, operators, contributors, and licensors from and against any and all claims, liabilities, damages, losses, inspection penalties, arbitration demands, and expenses (including reasonable attorneys' fees and legal costs) arising out of or in any way connected with:

  • Your physical construction, framing, masonry, electrical wiring, or earthwork execution based on calculations or diagrams from this Service.
  • Any structural defects, job-site injuries, material failures, or property damage occurring on projects where our estimation tools were used.
  • Your violation of any local municipal building code, state licensing statute, or third-party property rights.

7. Trademark & Non-Affiliation Disclaimer

All trade code designations, acronyms, and industry standards referenced across our website—including the International Residential Code (IRC), International Building Code (IBC), National Electrical Code (NEC / NFPA 70), ASTM International (ASTM), Air Conditioning Contractors of America (ACCA), and SAE International (SAE)—are the registered trademarks and intellectual property of their respective standards-authoring bodies.

BlueprintCalcs is an independent software calculation resource. The inclusion of these trade standards on our pages is strictly for model benchmark reference. BlueprintCalcs is not affiliated with, sponsored by, authorized by, or endorsed by the International Code Council (ICC), the National Fire Protection Association (NFPA), ASTM International, or ACCA.

8. DMCA Copyright Takedown Procedure

BlueprintCalcs respects the intellectual property rights of others. If you believe that any content, diagram, or formula on the Service infringes upon your copyrighted work under 17 U.S.C. § 512 (the Digital Millennium Copyright Act), please submit a formal notice to our designated copyright agent at [email protected] with the subject line [DMCA NOTICE] containing:

  • Identification of the copyrighted work claimed to have been infringed.
  • Exact URL and location of the allegedly infringing material on our Service.
  • Your contact information (name, physical address, telephone number, and email).
  • A statement of good faith belief and statement made under penalty of perjury that you are the copyright owner or authorized agent.

9. Permitted Use & Job-Site License

All proprietary source code, parametric SVG generation algorithms, design tokens, and CAD styling on BlueprintCalcs are owned by BlueprintCalcs.

Job-Site License: You are granted a free, perpetual, non-exclusive license to generate, download, print, and share 1-page cut sheets and blueprint diagrams generated by our tools for personal, commercial, and trade construction projects. You may not scrape, frame, clone, or programmatically re-sell our calculation engines as a competing software service without prior written consent.

10. Governing Law & Severability

These Terms shall be governed by and construed in accordance with standard applicable laws, without regard to its conflict of law provisions. If any provision of these Terms is found to be unenforceable or invalid under any applicable law, such unenforceability or invalidity shall not render these Terms unenforceable as a whole, and such provisions shall be deleted without affecting the remaining provisions herein.

11. Contact Information

For legal inquiries, terms interpretation, or permission requests, please reach out to:

BlueprintCalcs Legal & Compliance