BlueprintCalcs 2D Parametric Trade Tools

Watt Hours to Amp Hours Calculator

To convert Watt-Hours to Amp-Hours, divide total Watt-Hours by battery nominal voltage: Ah = Wh ÷ V. For example, a 2,400Wh energy requirement on a 12V battery bank requires 200 Amp-Hours. Multiply required capacity by depth of discharge buffer (1.11 for Lithium, 2.0 for Lead).

WH TO AH BATTERY CAD SCHEMATIC
200 Ah Nominal • 222.2 Ah (90% DoD)
DETAIL A: VOLTAGE INVERSE LAW VOLTAGE NOMINAL AH LiFePO4 AH 12V DC 200 Ah 222.2 Ah 24V DC 100 Ah 111.1 Ah 48V DC 50 Ah 55.6 Ah • Doubling voltage halves required Amp-Hours. • 48V systems use 75% smaller copper conductor gauge. TARGET ENERGY 2,400 Wh (2.40 kWh) System DC Bus Divisor: ÷ 12V DC ÷ YIELDS SIZED BATTERY BANK (Ah) 200 Ah NOMINAL CAPACITY (100% DISCHARGE) LiFePO4 Sized (90% DoD): 222.2 Ah Lead-Acid Sized (50% DoD): 400 Ah Energy Stored: 2.40 kWh PHYSICAL FORMULA: Electric Charge (Ah) = Energy (Wh) ÷ Nominal Voltage (V) Required Battery: 200 Ah Nominal | LiFePO4: 222.2 Ah | Lead-Acid: 400 Ah REAL-WORLD LITHIUM BATTERY SIZING (90% DOD): 222.2 Ah Never discharge lead-acid batteries below 50% state of charge to prevent permanent sulfation damage. ENERGY: 2,400 Wh | VOLTAGE: 12V DC | REQUIRED: 200 Ah Nominal (222.2 Ah LiFePO4)
✦ Direct Conversion: 2,400 Wh ÷ 12V = 200 Ah (222.2 Ah LiFePO4)
LiFePO4: 222.2 Ah Lead-Acid: 400 Ah
Nominal Ah 200 Amp-Hours
With Reserve 222.2 Ah (90% DoD)
100Ah Packs 3 Batteries
48V Equivalent 50 Ah High-Voltage

Energy Inputs & System Voltage

Direct Ah = Wh ÷ V
2,400 Wh
200Wh (Portable) to 15,000Wh (Home)
Battery Capacity Takeoff 200 Ah
Nominal Capacity:
200 Ah @ 12V
With 90% DoD Buffer:
222.2 Ah Total
At 24V (Same Energy):
100 Ah
At 48V (Same Energy):
50 Ah
100Ah Batteries Needed:
3 Packs
200Ah Batteries Needed:
2 Packs

How to Size Battery Amp-Hours from Watt-Hour Energy Budgets

When planning an off-grid solar installation, loads are almost always calculated in Watt-Hours or Kilowatt-Hours from appliance nameplates. Translating that energy demand into physical battery bank capacity requires 3 core steps:

1

Divide Stored Energy by System Voltage

Because Watt-Hours equal Volts times Amp-Hours, dividing total energy by the battery's nominal voltage yields the raw charge capacity: Ah = Wh ÷ V. A 2,400Wh load divided by 12V yields 200Ah. However, that same 2,400Wh divided by 24V requires only 100Ah, and at 48V requires just 50Ah.

2

Include Chemistry Depth of Discharge Buffering

Never buy a battery bank matching only your raw nominal Amp-Hours. Discharging deep-cycle lead-acid batteries beyond 50% severely damages lead plates and cuts cycle life from 600 cycles down to 150. A 200Ah lead-acid requirement demands a 400Ah battery bank (200 ÷ 0.50). Lithium LiFePO4 batteries allow 90% usable DoD, requiring only 222Ah (200 ÷ 0.90) to deliver 200Ah of usable energy.

Common Energy Demands (Wh) to Amp-Hours Across Standard Voltages

Energy Stored (Wh) Energy (kWh) 12V DC Battery 24V DC Battery 48V DC Battery Typical Application
600 Wh 0.6 kWh 50 Ah 25 Ah 12.5 Ah Portable Power Station, Camping
1,200 Wh 1.2 kWh 100 Ah 50 Ah 25 Ah Van Life, 12V Fridge + Starlink
2,400 Wh 2.4 kWh 200 Ah 100 Ah 50 Ah Off-Grid Tiny Home, Hunting Cabin
4,800 Wh 4.8 kWh 400 Ah (Heavy DC) 200 Ah 100 Ah Server Rack Battery Module
10,000 Wh 10.0 kWh 833 Ah (Impractical) 417 Ah 208 Ah Whole-Home Off-Grid Solar Storage

Engineering Rationale: Why Voltage Selection Dictates Battery Bank Efficiency

Ohm's Law & Conductor Cross-Section

When sizing battery systems from a known Watt-Hour daily load, Amp-Hours dictate wire gauge. Because power loss in copper conductors scales quadratically with current (P = I² × R), a 2,400Wh load discharged over two hours pulls 100 Amps at 12V, necessitating heavy 2/0 AWG pure copper cable to stay under 3% voltage drop. Converting the same Watt-Hour load to a 48V bus slashes discharge current to 25 Amps, allowing flexible and cost-effective 6 AWG wiring while minimizing heat dissipation in terminal lugs.

Cycle Life & DoD Derating Strategy

Rated Amp-Hours on a battery nameplate never represent 100% usable energy. Deep discharge beyond manufacturer thresholds drastically accelerates cathode degradation. Lithium Iron Phosphate (LiFePO4) chemistries maintain 3,000 to 5,000 cycles when cycled down to 90% Depth of Discharge (DoD), whereas traditional flooded or AGM batteries must never be discharged below 50% DoD without sacrificing cycle life down to fewer than 500 charge cycles. Always compute gross Amp-Hour capacity by applying the chemistry divisor.

Frequently Asked Questions About Converting Watt-Hours to Amp-Hours

How do you convert Watt-Hours to Amp-Hours? ↓

To convert Watt-Hours to Amp-Hours, divide the Watt-Hour value by the battery's nominal DC voltage: Amp-Hours = Watt-Hours ÷ Volts. For example, a 2,400 Watt-Hour energy requirement on a 12-Volt system requires 2,400 ÷ 12 = 200 Amp-Hours of battery capacity.

How many Amp-Hours is 1 kWh at 12V vs 48V? ↓

One Kilowatt-Hour (1,000 Watt-Hours) requires 83.3 Amp-Hours at 12 Volts (1,000 ÷ 12). At 24 Volts, it requires 41.7 Amp-Hours. At 48 Volts, it requires only 20.8 Amp-Hours. As system voltage quadruples, required Amp-Hours decrease by 75% for the exact same amount of stored energy.

How many 100Ah batteries do I need for 2,400 Watt-Hours? ↓

For a 12V system, 2,400Wh requires 200Ah nominal capacity. If using Lithium LiFePO4 batteries (90% usable DoD), you need 2,400 / 0.90 = 2,667Wh (222Ah), which requires three 100Ah 12V batteries wired in parallel. If using lead-acid (50% DoD), you need 4,800Wh (400Ah), requiring four 100Ah batteries.

Why should whole-home solar systems convert Wh to Ah at 48V? ↓

A standard modern home consuming 10 kWh (10,000 Wh) per day requires an unmanageable 833 Amp-Hours at 12V, necessitating massive copper cables and causing severe heat loss. At 48V, that same 10 kWh requires only 208 Amp-Hours, which is cleanly fulfilled by two standard 100Ah 48V server-rack batteries.

Solar & Power Calculators

Related Layout Tools

View Full Solar & Battery Power Hub 8 Tools →