Clean #57 Aggregate vs. Dense-Graded Base (Crusher Run)
Quarries process crushed limestone, granite, or trap rock to ASTM C33 and ASTM D2940 specs. Washed #57 clean aggregate (3/16" #4 sieve to 1") leaves roughly 40% void space for French drains and pipe bedding. Unlike a basic gravel calculator, sub-base sizing separates drainage rock from structural courses.
Crusher run (dense graded aggregate, DGA, or 21A) mixes 3/4-inch rock down to fine stone dust. Placed in 4-inch lifts, moistened, and rolled, those fines lock into a firm driveway base or paver sub-base.
Gradation Bulk Density & Compaction Factor Table
Quarry scales bill by net ton, so crews convert cubic yards using bulk density, tons per cubic yard, and a gradation compaction factor:
| Gradation | Sieve Size | Bulk Density | Tons / Cu Yd | Compaction | Primary Site Use |
|---|---|---|---|---|---|
| #57 Clean | 3/16" (#4) to 1" | 2,700 lbs/yd³ | 1.35 Tons | 5% - 8% | French drains, pipe bedding |
| Crusher Run / DGA | 3/4" to Dust | 3,000 lbs/yd³ | 1.50 Tons | 12% - 15% | Driveway base, paver sub-base |
| #411 Base Aggregate | 1/2" to Dust | 2,900 lbs/yd³ | 1.45 Tons | 10% - 15% | Shed pads, shoulder fill |
| #4 Ballast Stone | 1.5" to 2.5" | 2,600 lbs/yd³ | 1.30 Tons | 3% - 5% | Tracking pads, wet subgrade |
| Stone Dust / Screenings | 3/8" to Powder | 2,800 lbs/yd³ | 1.40 Tons | 15% - 20% | Flagstone joints, walkways |
How to Calculate Crushed Stone Tonnage: Contractor Protocol
Multiply length by width in feet for rectangular pads. For circular fire pits, divide diameter by 2 for radius and compute pi x r^2.
Divide depth in inches by 12: 3 inches equals 0.25 ft, 4 inches equals 0.333 ft, and 6 inches equals 0.50 ft.
Multiply area (sq ft) by depth (ft) and divide by 27. A 50 by 10 foot drive at 4 inches equals 6.17 cubic yards.
Add 5% to 8% settling for #57 clean stone, or 12% to 15% compaction for crusher run (DGA) with stone dust fines.
Multiply total yards by bulk density (1.35 tons/yd3 for #57; 1.50 tons/yd3 for crusher run) to book tri-axle dump truck deliveries.
Haulage Logistics: Legal GVW & Dump Truck Limits
Deliveries are capped by legal GVW and state DOT axle limits rather than bed volume alone:
- Single-Axle Dump Truck: 5 to 6 tons (3.7 to 4.4 yd³ of #57) for tight drives.
- Tandem-Axle Dump Truck: 12 to 14 tons (9 to 10.5 yd³) for residential lots.
- Tri-Axle Dump Truck: 18.5 to 20 tons net (13.5 to 14.5 yd³ of #57, or 12 to 13 yd³ of crusher run).
- End-Dump Tractor Trailer: 24 to 28 tons; requires wide turns and overhead wire clearance.
Subgrade Preparation, Geotextile Fabric & Drainage Slope
On soft subgrade soils, wheel loads push aggregate into clay while mud pumps into drainage voids. Crews prevent settlement with three steps:
- Match Geotextile Fabric: Use non-woven geotextile fabric (4-6 oz) for French drain filtration, and woven stabilization fabric under driveways on soft clay.
- Compact in 4-Inch Lifts: Run a 3,000-5,000 lbf plate compactor or heavy roller in 4-inch max lifts.
- Grade a 2% Cross-Slope: Pitch 1/4 inch per linear foot (2%) away from foundations so water drains instead of pooling.
Field & Quarry Ordering Notice
- Call 811 Before Digging: Request utility locates 48-72 hours before trenching or excavation.
- Scale Tickets & Geology: Weight runs 2,600-3,000 lbs/yd³ by limestone vs. granite geology and moisture; verify billed weight on quarry scale tickets.
- Geotech & Inspector Review: Consult a geotechnical engineer or verify with your local building inspector on soft clay, frost heave, or heavy RV loads.
- Driveway Permits: Confirm curb-cut setbacks and stormwater permeability rules with your local building department.